Using the BLE App to Configure ZIMO Scooters and Bikes
A comprehensive guide to connecting, configuring, and managing your ZIMO fleet vehicles using the BLE Debugger mobile application.
Levy Fleets Server Configuration
To connect your ZIMO scooter to Levy Fleets, configure these settings via the BLE app:
| Setting | Value |
|---|---|
| IP Address | 137.66.36.122 |
| Port | 9004 |
| BLE Key | wp0pZf6exeEJ2RFG |
Jump to Server Configuration for step-by-step instructions.
App Installation (Android)
The BLE Debugger app is required to configure ZIMO scooters and e-bikes via Bluetooth. This app allows you to connect directly to the vehicle's IOT module for configuration and diagnostics.
Download the App
The BLE Debugger app is available for Android devices. You can download it from:
- Download Link: https://www.pgyer.com/k13Y
- Password:
123456
This app requires an Android device. iOS is not currently supported.
Required Permissions
After installation, grant the following permissions:
- Location Access - Required for Bluetooth scanning on Android
- Storage Access - For saving log files and firmware updates
- Bluetooth Connectivity - Essential for communicating with the IOT module
- Background Running (Optional) - Helps maintain stable connection during configuration
Connecting via Bluetooth
Scanning for Devices
Open the App
Launch the BLE Debugger app on your Android device
Scan for Devices
Pull down on the screen to scan for nearby devices. Wait a few seconds for the scan to complete.
Find Your Device
Look for devices named "Scootor" (note the spelling). The device will show its MAC address and signal strength.
Device Identification
ZIMO devices appear as "Scootor" with a darker background color. Unknown devices appear as "UnKnow". Stay within 10 meters of the vehicle for best results.
Setting the Secret Key
You must enter the BLE key to establish a secure connection with the scooter.
Levy Fleets BLE Key: wp0pZf6exeEJ2RFG
Initiate Connection
Tap "Connect" next to your device to enter the Debug Scooter page
Set the Key
Tap "SET SECRET" in the top right and enter: wp0pZf6exeEJ2RFG
Save and Reconnect
Tap "Save", return to the Devices page, and tap "Connect" again
Successful Connection
After connecting, you'll see device information including IOT Version, ECU Version, Product ID, IMEI number, and ICCID (SIM card identifier).
Server Configuration
After inserting a SIM card, you need to configure the IOT module to connect to your fleet management server. Access this by tapping the menu (three dots) and selecting "Set IP".
Quick Note on MQTT Credentials
The BLE app connects to the scooter using a 16-character BLE secret key (not MQTT credentials). The MQTT username and password fields in the "Set IP" form are for the scooter's connection to your MQTT server.
Levy Fleets Configuration
Use these settings to connect your ZIMO device to Levy Fleets:
| Parameter | Value |
|---|---|
| IP Address | 137.66.36.122 |
| Port | 9004 |
| Name | KW |
| MQTT User | admin |
| MQTT Password | public |
Do Not Change APN
Leave the APN setting as-is. Do not modify the APN, Net User, or Net Password fields unless specifically instructed by your SIM provider.
After Configuration
- Tap "Setting" to send the configuration to the IOT module
- Send a "Reboot" command for changes to take effect
- Use "Read" to verify the settings were saved correctly
Commands Reference
The Commands panel provides direct control over vehicle functions. Tap the "Commands" button to access all available controls.
Power Controls
- Power-ON - Powers on the scooter. Buzzer will beep, headlight and taillight turn on.
- Power-OFF - Powers off the scooter. Buzzer beeps, lights turn off.
Light Controls
Configure time duration and flash mode:
| Mode | Behavior |
|---|---|
| 0 | Keep light on (solid) |
| 1 | Flash slowly |
| 2 | Flash fast (mode 1) |
| 3 | Flash fast (mode 2) |
Set Time to 0 to keep light on indefinitely.
Motor Lock Controls
- Lock-Motor - Activates EABS to lock the motor. Remains locked until unlock command.
- Unlock-Motor - Removes EABS lock. Scooter returns to previous state.
Ride Mode Settings
| Setting | Options |
|---|---|
| Ride Modes | ECO (efficient), D (standard), S (sport) |
| Speed Limit | 8-30 km/h |
| Idle Light | ON/OFF when stationary |
| Dual Driver | Enable both motors |
| Rear Light | Always On toggle |
| Kickstand Alarm | Toggle |
Information Commands
- Read Battery Info - Returns battery status, capacity, voltage, current, temperature, cycle count
- Read Scooter Info - Returns trip time/distance, speed, temperatures, total distance, battery levels
- Version - Returns IOT Version, ECU Version, and Product ID
System Commands
- Sleep Mode - Open/Close sleep mode. In sleep, only Bluetooth remains active.
- Battery Lock - Lock/Unlock the battery compartment cover (if equipped)
- Reboot - Restarts the IOT device. Required after configuration changes.
- Factory Reset - Restores all parameters to factory defaults
- Log-ON/OFF - Enable/disable diagnostic log output
Firmware Updates
Important: Before Updating
The scooter must be powered OFF before performing firmware updates. Only the IOT module should be active (connected via Bluetooth).
Update Process
Set Target Version
Click "Upgrade IOT" or "Upgrade ECU" button. Enter the version number (digits after decimal point only). Example: To update from V6.39 to V6.40, enter "40"
Download Firmware
Click "Confirm" to download the firmware from the server
Confirm Update
A dialog will show current and target versions. Click "CONFIRM" to proceed.
Wait for Completion
The update takes approximately 60 seconds. The IOT will automatically reboot.
Reconnect
After reboot, manually reconnect via Bluetooth to verify the update.
Diagnostics & Log Files
Log files are essential for troubleshooting connectivity issues and diagnosing hardware problems.
Capturing Logs
- Tap "Commands" and select "Log-ON"
- Wait 1-2 minutes to capture diagnostic data
- Tap the menu and select "Save log"
- Optionally tap "Upload Log" to send to support
- Send "Log-OFF" when finished
Log files are saved at: /Android/data/net.com.share.scooter.ble/files/log
RGB LED Status Indicators
(Available on certain models only)
Power ON (Solid)
| LED Color | Meaning |
|---|---|
| Green | Battery ≥ 50% |
| Yellow | Battery ≥ 20% |
| Red | Battery < 20% |
| Blue | Sleep Mode |
Power OFF (Flashing)
| LED Color | Meaning |
|---|---|
| Blue | Not connected to server |
| Green | Connected to server |
| Red | Hardware fault |
| Yellow | Firmware updating |
Need Help?
If you encounter issues configuring your ZIMO vehicles, contact our support team or visit the Troubleshooting section.